Gel Polish One Step Spark, 10 ml
SKU: 947155
Gel Polish One Step Spark, 10 ml by ReformA is a peach beige with a warm undertone and a dense fine shimmer. One step means base, colour and top are gathered in a single bottle: on a healthy plate Spark goes on with no separate base and no top coat.
Spark is the warmest of the four shimmer shades in CLEAN GIRL: the peach component pulls it away from the milky Glaze and puts it next to the coffee Naked in depth. Two thin coats, each cured separately, a 10 ml bottle with a brush.
Specification
- Product type: one step 3-in-1 gel polish
- Colour: a peach beige, warm undertone
- Effect: a dense fine shimmer
- Volume: 10 ml, bottle with a brush
- Formula: TPO-free, HEMA-free and DI-HEMA-free
- SKU: 947155
- Manufacturer: ReformA
Use it for
- A warm manicure with a glow, on its own or as an accent.
- A beige ground with a shimmer already in it, with no extra layer.
- Express work: one product instead of three.
- Pedicure, where the coating has to stay thin.
- More warm shades in the beige gel polish section, the full 10 ml colour line here.
How to apply
- Do the manicure with a cuticle remover: place a drop on the cuticle, push it back and take off the pterygium down to a clean, dry plate.
- Go over the surface of the nail with a 180 grit file and remove the dust. A single-phase formula holds by mechanical adhesion, so this step is not skipped.
- Degrease the plate with Duo Prep and stop touching the nail with your fingers from this point on.
- Apply the first thin coat of Spark straight onto the plate, with no base. Keep the hand in the air and do not touch the underside of the free edge with the brush. Cure.
- Apply the second coat to the final result and cure.
- No top coat is needed: the finishing components are already in the Spark formula.
- Apply cuticle oil no earlier than 30 seconds after the last coat is cured.
On healthy nails Spark works with no base and no top coat, that is what one step technology is. If the plate is thin or bendy and the hands tend to sweat, apply an acid-free primer before the colour, and a base coat as well if you need it: on that kind of plate the mechanical adhesion of a single-phase formula may not be enough.
Curing time: 60...120 sec in an LED lamp. The time depends on the power of the lamp and on the diodes themselves, and has to be checked separately for each product.
Frequently asked questions
How do I remove one step gel polish?
The same way as a classic gel coating: break the surface with a file so the remover can get in, then soak off with wraps or take it down with an e-file. Spark is not peeled off: a single-phase film sits directly on the plate, and peeling takes plate with it. Products for this are in the removal section.
Is one step gel polish suitable for beginners?
Yes, and it is the usual entry point, because there are fewer products and fewer steps to get wrong. What it does not forgive is preparation: with no base coat underneath, everything the prep misses shows up as lifting in the first week.
Can I use chrome powder over one step gel polish?
Not directly. Chrome powder needs a no-wipe top coat with the right tack, and Spark ends the scheme without one. If you want chrome, treat Spark as a colour coat, put a suitable no-wipe top over it and work the powder on that. The shimmer already in Spark is a separate effect and needs nothing on top.
What is the most common mistake people make with one step gel polish?
Treating it as a polish rather than as a gel: skipping the buff, applying one thick coat instead of two thin ones, and not sealing the free edge. All three come from the same assumption, that fewer products means fewer rules. The product list is shorter; the technique is not looser.
The colour on screen may differ from the real shade of the product: monitor calibration and the display modes you have switched on both affect it. If you have any doubt about the shade, get in touch and we will show you the colour in person.
Not tested on animals